寻找当地的油漆工和装饰师在泰晤士河上的金斯敦

嗨，novice_40，首先，祝你的项目好运-我希望你喜欢它。新粉刷的墙壁/天花板在油漆开始前总是需要适当密封(否则油漆会停留在表面并很容易脱落)。你可以通过涂抹几层乳液“雾涂层”(将初始溶液的比例为60:40的水稀释成乳液，然后按相反的比例涂第二层雾涂层，以增加覆盖范围，但仍然足够多水，使其继续沉入下面的石膏中)。或者，就像汤姆建议的那样，你可以买一个特制的底漆。如果抹灰工对墙壁“过度抛光”，后一种选择将是最好的，因为抹灰将不能让雾涂层渗透和正确附着。如果你有一个很大的面积/几面墙，那么对你来说最经济有效的方法将是雾涂层-这是一个行业标准和完全可以接受的方法。普通的白色乳剂是合适的，既便宜又容易获得。从石膏的最低点开始涂抹，然后用滚筒向上涂抹。雾层干得很快&这种自下而上的方法可以防止你在石膏上得到油腻的油漆飞溅。用刷子把边缘剪开。 if the ceiling is also bare, then progress onto the ceiling. within the hour, your walls will be ready for the second mist coat. apply this in the same order as the first. a word of caution: even with the best intentions, mist coats can involve a bit of splashing, so make sure your flooring is protected & the sockets temporarily turned off & covered. once the 2 mist coats have fully dried you can more easily assess the plasterer's handiwork. use a spatula to fill any minor dents & give these a light sanding, once cured. anything major & get the plasterer back to resolve it. you don't want to be sanding down large areas of plaster, as this will cause a rough & spoilt finish that will need copious filling & sanding to put right. now, use a proper water-based wood primer for your bare woodwork - for the same reasons as you need to seal fresh plaster. a primer-undercoat is perfectly suitable - though you will need 2 coats: one to prime, a second to undercoat. a third coat is optional, but we'll get to that in a mo. alternatively, you can buy 2 separate paints: one a specified wood primer & the second a specified undercoat. whilst the primer should be water-based, the undercoat can be oil-based - though only if your satinwood is also oil-based. this method can improve the longevity of the finish. once your primer/first layer of primer-undercoat is dry, caulk your woodwork. next, move back to your ceiling/walls. this time begin with the ceiling (either silk or matt are suitable finishes - but silk is a more reflective surface that draws the eye & can accentuate any imperfections). get your first coat on. cut in free-hand, moving your brush from 1/2 inch away from the corner inwards towards the join as your hand steadies & finds the line. don't try to leap straight into the corner unless you've got a steady hand. whether you cut in before or after rollering is down to personal preference. i prefer beforehand as it avoids a visible 'tram line' created by dragging your brush through a rollered section. whichever you choose, ensure you keep a wet edge (ie: don't allow the paint to dry between cutting in & rollering). allow the edges to dry, then move down to the walls. get your first coat of dulux endurance on. cut in free-hand. once dried, repeat the process for your second coats. if you are prepared to wait up to a couple of days between coats (dep. on drying conditions) for the paint to fully cure, you can use (yellow) frog tape to help you achieve a clean line between surfaces. be very careful when removing it however, as this can pull the paint back off if it isn't fully cured. finally, give your woodwork a light sanding to remove any splashes of paint & nibs of rough wood fibres. ideally, apply another undercoat, to improve the coverage & durability, then (when dry) apply your satinwood top coat. again, if you're happy the walls have cured sufficiently, frog tape can give you a razor sharp line where the satinwood meets the emulsion. take care when peeling it away. there you have it! any questions, feel free to give me a holla. meantime, i hope this helps. happy painting! best, alix james decorators

油基光泽会随着时间的推移而褪色和变黄，因为含油量到达表面导致变色。今后不要使用油基涂料。使用水性光泽，蛋壳和缎面代替。这些水性涂料自从首次进入市场以来，随着时间的推移，效果越来越好。我要分享一个我的商业秘密…当我在现有的油基漆上涂水基光泽、蛋壳等时，我不想花几个小时过度擦拭，以便在两种漆之间提供良好的粘结，否则它们不会很好地结合在一起。所以我用了一种特殊的水基颜料，它可以“蚀刻”到几乎任何表面上，所以它会把自己锁在光泽上!然后，在特殊的水基蚀刻漆上绘制新的水基涂料系统。例如，如果你在做纺锤，你不会相信这节省了多少时间。这是油漆:zinsser 123加上(是的，愚蠢的名字!)http://www.zinsseruk.com/product/bulls-eye-1-2-3-plus/你通常只能从装饰贸易商店，如leyland和brewers购买，或在网上订购。这不是市场上最便宜的油漆，但根据我的经验…一分钱一分货! all the paints and products i use are the most expensive on the market but my workmanship lasts and i save huge amounts of labour time when on a job by using the tools, paints and products. follow my trade top tips and you'll too achieve results you wouldn't otherwise be able to!!! happy painting

1、用矿物酒精和抹布彻底清洗表面。2、用木材填充物填满任何凹痕或钉孔，根据使用说明选择特定的木材填充物。3、用细级砂纸轻轻打磨表面，直到表面的光泽面全部清除。4、用吸尘器将待涂区域的砂纸上的灰尘清除干净。5、表面打底油基金丝底漆。6、等待底漆完全干燥。7涂2层多乐士贸易底漆。8、涂抹1至2层多乐士贸易光泽。我希望这能有所帮助。马特

嗨，最好的方法是先在天花板和墙壁上涂乳液(先覆盖所有大的区域)，你通常需要涂2层。然后把它切成乳剂，完成你的光泽。对不起，我应该告诉你，确保所有区域没有灰尘，门上面和沿裙边。希望这能有所帮助。